SWANS/HiVi In-Wall Speakers
For custom, integrated-decor installations Swans also offers high-quality solutions
without compromises in sound.
Feature highlights:
The adjustable fabric tweeters powered by neodymium magnets ...
The very pleasant-sounding high-resolution silk-dome tweeters are freely positionable to 30° therefore can be tuned ideally to almost any listening position. Because of the custom front panel a very smooth dispersion with a large "sweet spot" is achieved.
High-quality crossover ...
Depending on the model, 6, 12 or 18 db versions were used. The tweeters are protected against overload by an auto-reset circuit while their output is adjustable in three settings depending on location of installation and the acoustics.
Robust and practicable design ...
The frame consists of structurally reinforced, paintable, long lifespan PP-plastic. All grills are made of oxidation-resistant aluminum with stainless steel mounting hardware. These units and their very robust chassis were designed for installations with an undefined volume yet can also be optimized as a full-range system. They are made to perform flawlessly for a long long time. High-quality terminals and heavy-gauge internal wiring are standard.
We know how demanding custom installation clients can be and are aware of the priorities contractors need to fulfill. We are confident that our units set benchmarks for others to meet. Outstanding fidelity, longevity and favorable bottom-line are our hallmarks!
Grills, installation templates, accessories and painting covers are included in every system!
SWANS/HiVi VX5-W
VX5-W
5.25” 2-way In-Wall Speaker
Woofer: 5.25” PP cone, rubber surround, 12.5oz Magnet, 1" voice coil, bumped back plate, vented pole piece
Tweeter: Swivel 30 degrees, 0.8" Silk dome, Ferro-fluid cooled, Neodymium magnet, wide dispersion
Crossover: Phonalic PCB board, 12dB woofer section, 18dB tweeter section, Polymide auto protective reset switch for tweeter
Frequency Response: 50Hz- 20KHz
Sensitivity: 87dB
Recommended amplifier power: 10-80 watts
Impedance: 8 ohm jumper
Cut Out Size: 266mm x 181mm
SWANS/HiVi VX6-W
VX6-W
6.5” 2-way In-Wall Speaker
Woofer: 6.5” PP cone, rubber surround, 18.5oz Magnet, 1" voice coil, bumped back plate, vented pole piece
Tweeter: Swivel 30 degrees, 1" Silk dome, Ferro-fluid cooled, Neodymium magnet, wide dispersion Crossover: Phonalic PCB board, 6dB woofer section, 6dB tweeter section, Polymide auto protective switch for tweeter
Frequency Response: 50Hz- 20KHz
Sensitivity: 88dB
Recommended amplifier power: 10-100 watts
Impedance: 8 ohm
Cut Out size: 276mm x 189mm
SWANS/HiVi VX8-W
VX8-W
8” 2-way In-Wall Speaker
Woofer: 8” PP cone, rubber surround, 21.8oz Magnet, 1.4" voice coil, bumped back plate, vented pole piece
Tweeter: Swivel 30 degrees, 1" silk dome, Ferro-fluid cooled, Neodymium magnet, wide dispersion Crossover: Phonalic PCB board, 12dB woofer section, 18dB tweeter section, Polymide auto protective reset switch for tweeter
Frequency Response: 39Hz- 22KHz
Sensitivity: 88dB
Recommended amplifier power: 10-125 watts
Impedance: 8 ohm
Cut Out size: 326mm x 226mm
SWANS/HiVi VX5-LCR
VX5-LCR
5.25” In-Wall Video Shielded
Left, Center or Right Channel Speaker
Woofer: 5.25” PP cone, rubber surround, 18.5oz Magnet, 1" voice coil, bumped back plate, vented pole piece
Tweeter: Swivel 30 degrees,19mm silk dome, Ferro-fluid cooled, Neodymium magnet, wide dispersion
Crossover: Phonalic PCB board, 6dB woofer section, 12dB tweeter section, polymide auto protective reset switch for tweeter
Frequency Response: 55Hz- 22KHz
Sensitivity: 87dB
Recommended amplifier power: 10-125 watts
Impedance: 8 ohm
Cut Out Size: 414mm x 188mm
SWANS/HiVi VX10-SW Installable-Subwoofer
VX10-SW
10” In-Ceiling SubWoofer
Woofer: 10” PP cone, rubber surround, 33oz Magnet, 1" voice coil, bumped back plate, vented pole piece
Frequency Response: 23Hz- 500Hz
Sensitivity: 84dB
Recommended amplifier power: 10-200 watts
Impedance: 8 ohm
Cut Out size: 311mm
